top button
Flag Notify
    Connect to us
      Site Registration

Site Registration

arptables FORWARD chain not working

+2 votes
1,284 views

I tried using arptables on a linux internet gateway to filter out packets that have the source MAC address of the internet connected interface but not its IP address (see below).

I didn't get any hits, although I now there were packets matching the rule. The same rule in the OUTPUT chain works as expected (by me at least) . Is there something else I need to do to use the FORWARD chain?

arptables -I FORWARD 1 -o eth0.164 --source-mac 00:24:E6:00:00:3E -s ! x.x.x.x -j DROP
arptables -I OUTPUT 1 -o eth0.164 --source-mac 00:24:E6:00:00:3E -s ! x.x.x.x -j DROP

posted Dec 24, 2013 by Dewang Chaudhary

Share this question
Facebook Share Button Twitter Share Button LinkedIn Share Button

1 Answer

+1 vote

ARP packets generated by the host go through the OUTPUT chain. The FORWARD chain sees only bridged ARP packets, which are received but not generated by the host. Is your gateway acting as a bridge ?

answer Dec 24, 2013 by Meenal Mishra
Similar Questions
+5 votes
IPTable: How to forward http traffic to two IPs

I want to forward all http traffic coming in from a perticular IP at local port 8080, to 2 particular IP Addresses (port 80). Is it enough to prepend the following in my IPtable

-A PREROUTING -s xx.xx.xx.xx/24 -p tcp --dport 8080 -j DNAT --to-destination xxx.xxx.xxx.xxx:80
-A PREROUTING -s xx.xx.xx.xx/24 -p tcp --dport 8080 -j DNAT --to-destination yyy.yyy.yyy.yyy:80

+2 votes
Can not see VM packets using Netfilter

I’m recently developing a simple program using netfilter and I’m having a tricky problem. My program is mainly to log the src and dst ip address of all the packets. This program is run in the host machine. I have several virtual machines on that host machine.

The problem is, I can not capture the packets generated or destined at the VMs. All the VMs use bridging network to connect.

Can anyone help me?

+1 vote
How to set multihop gateway rules for forward table?

My network is like this:

GW+DHCP 192.168.1.1, eth0:192.168.100.1 eth1:192.168.168.1.1
HOST1+DHCP 192.168.1.100, eth0:192.168.1.100 eth1:192.168.2.1
CLIENT1 192.168.2.100

There is a double NAT here at both GW and HOST1. The DHCP from GW is only towards the eth1 network and subnet. The DHCP from HOST1 is only towards eth1.
In GW there is a masquerade rule which works fine and allows all forwarded packets.

I do not want packets from clients in the CLIENT1 side of the network to get access using the nat to the local network resources but that they will have access to the internet using GW. So basically I want to allow all forwarded traffic from the 192.168.2.0/24 network to be allowed to all networks but not the localnet and the local GW resources.

I am a bit in a conflict in it since the next rules should work or at least should do the trick..:

-A FORWARD -s 192.168.2.0/24 -i eth1 -p tcp -m state --state ESTABLISHED -j ACCEPT
-A FORWARD -i eth1 -p icmp -j ACCEPT
-A FORWARD -s 192.168.2.0/24 -i eth1 -p tcp -m multiport --dports 53,443,80,21,22,23,110,25,143,995,993,3128,8080 -j ACCEPT
-A FORWARD ! -i eth1 -m state --state NEW -j DROP
-A FORWARD -o eth1 -j ACCEPT
-A FORWARD -d 192.168.1.0/24 -j DROP

Before I press the "save" button I would like for someone else to take a small look at it.

+1 vote
How to check whether any netfilter rules are set on a host

Is there a way to find out if there any iptables rules set on a machine ?

There are some indirect ways which will not always work; for example, I know that on most hosts, iptables -S will return the following output (when no iptable rules are set)
-P INPUT ACCEPT
-P FORWARD ACCEPT
-P OUTPUT ACCEPT

So you can check whether or not the number of output lines is greater than 3 (as an indication of whether or not iptables rules are set). But there are hosts on which there are more chains then these 3; these chains are set by application/services, even without any iptable rules which are set. And after running iptables -F on these machines, iptables -S will still show more than 3 chains, even that there are no iptables rules set in these chains.

So the question is - is there a way to know whether or not netfilter rules are set on a host, regardless of the number of chains ?

0 votes
How to bind NF_ARP family in netfilter queue

Is it possible to bind multiple address families in netfilter queue? I see IPv4 show up in my queue, but not ARP. With error code removed, here is how I'm calling nfq_bind:

netfilterqueue_handle = nfq_open();
netfilterqueue_queue = nfq_create_queue( netfilterqueue_handle, 0,

nfq_bind_pf( netfilterqueue_handle, AF_INET );
nfq_bind_pf( netfilterqueue_handle, NF_ARP );

I'm thinking the more likely possibility is the iptable rules I'm using to send traffic to the queue are too restrictive. Here are the rules I have:

# Generated by iptables-save v1.4.21 on Sat Feb 14 10:40:46 2015
*nat
:PREROUTING ACCEPT [161:14105]
:INPUT ACCEPT [56:4995]
:OUTPUT ACCEPT [56:4496]
:POSTROUTING ACCEPT [56:4496]
-A POSTROUTING -s 10.0.1.0/24 -o eth0 -j MASQUERADE
COMMIT
# Completed on Sat Feb 14 10:40:46 2015
# Generated by iptables-save v1.4.21 on Sat Feb 14 10:40:46 2015
*filter
:INPUT ACCEPT [1017:217421]
:FORWARD DROP [53:2307]
:OUTPUT ACCEPT [934:211104]
:MYRA - [0:0]
-A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j MYRA
-A FORWARD -s 10.0.1.0/24 -o eth0 -m conntrack --ctstate NEW -j MYRA
-A MYRA -j NFQUEUE --queue-num 0 --queue-bypass
COMMIT
# Completed on Sat Feb 14 10:40:46 2015

Do I have to add another FORWARD line to get ARP to jump to MYRA? What would it look like?

...